
Water Pressure Problems Boronia
Weak shower, banging pipes, or taps that splash and hammer? Pressure problems are common on Boronia's slopes. We test, diagnose and fix low and high water pressure. Ring 03 8804 5837.
- Licensed Victorian plumbers
- Based in Boronia, City of Knox
- Price agreed before work
- Night and weekend call-outs
Low water pressure
Low pressure turns a shower into a dribble, makes the washing machine slow to fill and leaves upstairs fixtures weak. In Boronia homes, the usual causes are:
- Galvanised steel pipe that has rusted inside, narrowing the bore.
- Partly closed valves, including a stopcock not fully reopened after a repair.
- A failing pressure limiting valve stuck partly closed.
- A hidden leak on the water service or under the house.
- Undersized pipework, common when houses have been extended without upgrading supply.
- Blocked aerators and shower heads with scale or debris.
- Location. Houses at the top of steep streets toward The Basin can have lower mains pressure, especially at peak times.
If only one tap is weak, the problem is likely at that tap. If the whole house is weak, it is the supply.
High water pressure
High pressure is less obvious but more damaging. Houses lower down Boronia's slopes can see mains pressure well above what tapware, hot water units and appliances are designed for. Signs include:
- Taps that splash hard even when barely open.
- Banging or shuddering pipes when taps close, called water hammer.
- Hot water relief valves dripping often.
- Toilet inlet valves and tap washers wearing out quickly.
- Flexible hoses and appliance valves failing early.
Excessive pressure shortens the life of every fitting in the house and can void appliance warranties.
How we test
We fit a pressure gauge to a tap near the meter and read the static pressure. Then we test flow at key points. We check the pressure limiting valve if you have one, the stopcock and the pipework type. That tells us whether the issue is mains pressure, your pipes or a fixture.
Solutions
Pressure limiting valves
A pressure limiting valve fitted after the meter reduces mains pressure to a safe level for the whole house. Victorian rules set maximum pressures for internal plumbing in new work. We supply and install PLVs, and replace old ones that have failed.
Replacing galvanised or undersized pipe
Where old pipe is the cause, replacing it with copper or modern pipework restores flow. We can replace just the worst sections or repipe the house.
Water hammer arrestors
Arrestors absorb the shock when quick-closing valves in washing machines and dishwashers shut, quietening banging pipes.
Pressure pumps
Where mains pressure is genuinely low at the top of a hill, a pressure pump can boost supply. We check with you whether that is the best answer.
Cleaning or replacing fixtures
Sometimes all it takes is a new cartridge, aerator or shower head.
Why pressure varies so much in Boronia
Water pressure at your meter depends largely on the height difference between your property and the reservoir or pumping station that supplies it, plus how much water everyone else on the line is drawing at the time. Boronia's land rises from around the flat land near Bayswater and the railway line up toward the foothills, and the change in height between streets can be significant. Two houses a few streets apart can have very different pressure at the meter.
That is why a one-size answer does not work. A pressure limiting valve that solves banging pipes in a house at the bottom of a hill would make things worse at the top. We test first and recommend based on your readings.
Pressure and hot water units
Mains pressure hot water units have a relief valve that opens if pressure in the tank gets too high. In a house with high mains pressure, that valve releases water far more often than it should, and hot water units can wear out early. Most installations include an expansion control valve on the cold side, and many need a pressure limiting valve too. If your relief valve is always dripping, ask us to test your mains pressure as well as the valve itself.
Pressure after renovations
Adding a second bathroom, a rain shower head or a new kitchen mixer can expose weak supply that was never noticeable before. If pressure dropped after building work, the cause may be an undersized connection between the old and new plumbing, a valve that was left partly closed, or debris in new pipework. We trace it back and fix it.
Water pressure across Knox
We fix pressure problems in Boronia, Bayswater, Wantirna, The Basin, Ferntree Gully, Upper Ferntree Gully, Knoxfield, Sassafras and Heathmont. Our guide to low water pressure in hills homes has checks you can do first.
Pressure and new appliances
Many dishwashers, washing machines and fridges with water connections specify a pressure range. If yours is outside it, appliances may not work properly or may fail early. We can test and advise.
Read this first
What you get with water pressure problems
- In the van
- Drain camera and locator, high-pressure jetter, drain machine, acoustic leak detector, thermal camera, pressure gauges
- Licensing
- Victorian licences for water supply, sanitary, drainage and roofing
- Quoting
- Cause explained and price agreed before work, written quotes for larger jobs
- Parts
- WaterMark-certified fittings and products that meet Australian Standards
- Certificates
- Compliance certificates for regulated plumbing work, photos for your records or insurer
- Leaving
- Old parts removed, the work area cleaned and everything tested with you
Send us the job details
Send the details and a licensed plumber from Boronia will call you back. Water flooding or a sewer overflowing? Do not wait for a reply, ring 03 8804 5837 now.
Every job is quoted on what we actually find. That is why you will not see a price list on this site.
Water Pressure Problems in Boronia: questions
Why is my water pressure low?
Common causes are rusted galvanised pipe, a partly closed valve, a failed pressure limiting valve, a hidden leak or undersized pipework.
Can water pressure be too high?
Yes. High pressure causes water hammer, dripping relief valves and early failure of taps, hoses and appliances.
What is a pressure limiting valve?
A valve after the meter that reduces mains pressure to a safe level for your home's plumbing.
Why do my pipes bang when I turn off a tap?
That is water hammer, usually caused by high pressure or loose pipes. A PLV or hammer arrestor usually fixes it.
Can you test my water pressure?
Yes. We test static pressure and flow and explain what the readings mean.
Will a new shower head fix low pressure?
Only if the old one is blocked. If the whole house is weak, the problem is the supply.
Local, careful and upfront
Sloping blocks, heavy clay, gum and elm roots in old earthenware sewers, 1970s brick veneers and newer townhouse rows: Boronia plumbing has its own habits and we know them.
Cause and cost before work starts. If something changes once a wall or a drain is open, we stop and talk it through with you.
Camera inspections, high-pressure jetting, acoustic and thermal leak detection, pressure testing. We look before we dig.
Water supply, sanitary, drainage and roofing work by licensed plumbers, with compliance certificates lodged where the law needs them.
More plumbing services around Boronia
Suburbs we cover from Boronia
We are based in Boronia and work the Knox side of the Dandenong foothills: Bayswater and Wantirna to the north and west, The Basin and Sassafras up the hill, Ferntree Gully, Upper Ferntree Gully and Knoxfield to the south, and Heathmont over the Maroondah line. Somewhere else nearby? Ring 03 8804 5837 and ask.
Plumbing problem in Boronia?
Ring a local licensed plumber. You hear the price before any work starts.